WonderMedia Technologies, Inc.
W-Load Version : 0.19.00.01
ethaddr............found


U-Boot 1.1.4 (Oct  8 2010 - 10:39:28)
WonderMedia Technologies, Inc.
WMT U-Boot Version : 0.12.01.00.27
U-Boot code: 03F80000 -> 03FC87A4  BSS: -> 04019DAC
RAM Configuration:
Bank #0: 00000000 128 MB
boot from spi flash.
flash:
     Bank1: FFF80000 -- FFFFFFFF
     Bank2: FF780000 -- FFF7FFFF
Flash:  8.5 MB
In:    serial
Out:   serial
Err:   serial
bootcmd="run usblogocmd;run usblogocmd2;run nandlogocmd;logo show"
LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10,
d8110500|10
PWM param (setting): 0,5,599,449,539,299,30,0,27
LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000
Execute register operation for LCD:
  reg op: 0xD8110508 | 0x10
  reg op: 0xD8110504 | 0x10
  reg op: 0xD8110500 | 0x10
PWM0 input freq = 47916666 Hz, output freq = 15998 Hz
PWM0 register setting: scalar = 4, period = 598, duty = 448
LCD init OK
"Loading OS Image ..."
usb usb1: Product: USB Host Controller
usb usb1: Manufacturer: Linux 2.6.10_dev-VT8610 ehci_hcd
usb usb1: SerialNumber: pci-echi
 1-0:1.0: USB hub found
 1-0:1.0: 2 ports detected
locktree(): line: 1024: this function not completed
usb 1-+11111111010000: new high speed USB device using abc and address 2
usb 1-+11111111010000: Product: USB2.0 Hub
       scanning bus for storage devices... 0 Storage Device(s) found

** Invalid boot device **

** Invalid boot device **
maddr = 0x3c00000, naddr = 0x3e00000

<1> Read header
find NAND Flash SAMSUNG_K9GAG08U0M
nfc 0x1324 , divisor b
block4095 tag=74624230  version =1
block4094 tag=62743142  version =1
Un-know id = 0x0
Read finsih
Header is 0x00119436 0x80101000

<2> Read Data
Read finsih
show logo .....
LCD already initialized
Loading BMP .....
colorBits = 24
logo_width = 800, logo_height= 480
lcd_width= 800, lcd_height = 480
ok
REG32_VAL(0xd8000440) = 0x08080800
memory size: 128MB
### main_loop entered: bootdelay=1

Execute register operation:
  reg op: 0xD8110064 | 0xC
  reg op: 0xD811008C | 0xC
  reg op: 0xD81100B4 & 0xFFFFFFFB
  reg op: 0xD81100B4 | 0x8
  reg op: 0xD8130054 | 0x1
### main_loop: bootcmd="run usbbootcmd;run usbbootcmd2;run nandbootcmd;go 100000
"
Hit Enter key to stop autoboot:  0
ATSMB Host 390KHz
Found SD Card

scriptcmd start:
ATSMB Host 390KHz

SD2_0  : SDHC card!

Init  : card selected !

SD:Four Bits Mode!
SD Card High Speed!

Initial SD Card OK!
ATSMB Host 25MHz
SD clock is 25Mhz
register mmc device
## Valid DOS partition found ##
part_offset : 3f, cur_part : 1
--> fatload mmc 0 0 script/scriptcmd
## Valid DOS partition found ##
part_offset : 3f, cur_part : 1
reading script/scriptcmd
Tina_Match: isdir 0x1######################
mydata :
Size of clusters in sectors : 80
The sector of the first cluster, can be negative : 90
Current FAT buffer : 03f4d440
fatbufnum : ffffffff
Length of FAT in sectors : 9c
Size of FAT in bits : 10
Starting sector of the FAT : 38
Start sector of root directory : 170

0xA9 bytes read
## Executing script at 00000000
** Script length: 97
** exec: "lcdinit"
LCD param (setting): 1,30000,8,800,480,48,40,40,3,29,13,d8110508|10,d8110504|10,
d8110500|10
PWM param (setting): 0,5,599,449,539,299,30,0,27
LCD FrameBuffer = 0x07600000, BMP Address = 0x03C00000
Execute register operation for LCD:
  reg op: 0xD8110508 | 0x10
  reg op: 0xD8110504 | 0x10
  reg op: 0xD8110500 | 0x10
PWM0 input freq = 47916666 Hz, output freq = 15998 Hz
PWM0 register setting: scalar = 4, period = 598, duty = 448
LCD init OK
** exec: "fatload mmc 0 0 /script/uzImage.bin"
## Valid DOS partition found ##
part_offset : 3f, cur_part : 1
reading /script/uzImage.bin
Tina_Match: isdir 0x1######################
mydata :
Size of clusters in sectors : 80
The sector of the first cluster, can be negative : 90
Current FAT buffer : 03f4c0e8
fatbufnum : ffffffff
Length of FAT in sectors : 9c
Size of FAT in bits : 10
Starting sector of the FAT : 38
Start sector of root directory : 170

0x265F08 bytes read
** exec: "setenv bootargs mem=112M root=/dev/mmcblk0p2"
** exec: "bootm 0"
## Booting image at 00000000 ...
   Image Name:   Slackware GNU/Linux 2.6.36
   Image Type:   ARM Linux Kernel Image (uncompressed)
   Data Size:    2514632 Bytes =  2.4 MB
   Load Address: 00008000
   Entry Point:  00008000
   Verifying Checksum ... OK
OK
No initrd
## Transferring control to Linux (at address 00008000) ...

Starting kernel ...

Uncompressing Linux.............................................................
................................................................................
.................. done, booting the kernel.